Overview
The WAC202 classroom has a touchscreen a/v controller, wall-mounted data/video projector, wall-mounted speakers, ēnointeractive whiteboard, connections for laptops and HD devices, and microphone ports for assistive listening devices. The MI 207 is a general-use classroom located on the second floor of Morse-Ingersoll Hall. Instructional technology in this space includes a pull-down projection screen, ceiling-mounted projector, and an a/v lectern housing a classroom computer, Blu-Ray player, speaker, and connections for a laptop.
The information below documents how to accomplish common tasks with the a/v equipment in the room.Table of contents
| Table of Contents | ||
|---|---|---|
|
|
Projecting the built-in DVD/VCR:
- The active source button will be change to white.
Projecting the built-in document camera:
- The active source button will be change to white.
- The LED ring on the on the power button will glow BLUE when the doc cam is On.
- The LED ring on the power button will glow RED when the doc cam is Off.
Capacity |
|---|
30 |
Furniture |
|---|
8 tables, 18 chairs, 12 tablet arm desks, |
12ft chalkboard, |
two 18ft chalkboards, instructor's lectern. |
Technology |
|---|
Ceiling-mounted data/video projector, |
manual projection screen, instructor's a/v |
lectern with |
Blu-Ray player, |
Windows computer, speaker. |
Special Notes |
|---|
|
Projecting from a laptop or other video device:
Connect one of the video cables (VGA or HDMI) from the cable cubby to the corresponding port on your laptop/device.
If you need to be away from the a/v cabinet, there is also a long cable tether on the hook on the left side of the podium that may be used to hookup to the laptop/device.
Mac laptops and mobile devices may require a display adapter.
For audio with VGA, plug the 3.5mm audio cable into the headphone/audio out port on your laptop/device.
Press the On button on the touchscreen Crestron a/v controller to activate the room a/v system.
Press the Power button to boot up the laptop/device.
Select the source that you have the laptop plugged into - either VGA or HDMI.
The active source button will be change to white.
Audio level can be adjusted using the Volume buttons on the right side of the controller.
When you are finished using the equipment, please press the Off button and then Yes confirm to shut down the a/v system.
Projecting the built-in Blu-Ray player (U.S. formatted content):
Note: Blu-Ray players are compatible with Blu-Ray discs, DVDs and audio CDs.
- The active source button will be change to white.
Projecting the built-in Blu-Ray player (Non-U.S. formatted content):
The Blu-Ray player in this classroom is capable of playing DVD or Blu-Ray discs from any region of the world.
International DVD:
DVD regions are set automatically by the player, so just insert your disc and follow the directions on page three.
International Blu-Ray:
Switching Blu-Ray zones must be done using the remote control (top rack drawer in the podium). Follow the directions below to switch between the different Blu-Ray zones:
- Start with the Blu-Ray player Off.
- For Zone A, press 1 + Power.
- For Zone B, press 2 + Power.
- For Zone C, press 3 + Power.
- Turn the player On.
- Once you have set the Blu-Ray zone, insert your disc and follow the directions on page three.
- Please remember to return the Blu-Ray remote to the top rack drawer in the podium once you are done using it.
Troubleshooting
If you encounter a Blu-Ray Region Code Error, check the following settings:
- Go to Settings and make sure that Quick Start is set to Off.
- Go to Video Options and set the Last Memory option to Off.
- Repeat the Zone setting steps above.
Projecting the built-in computer
Press the Power button on the projector remote to activate the projector.
Press the Power button on the upper right corner of the computer to boot the unit.
Once the projector display comes up, press the Computer 1 button on the remote to display the computer.
Audio volume can be adjusted on the computer using the speaker icon in the taskbar (lower right corner near the clock) or by using the audio adjustment dials on the front of the speaker.
When you are finished using the equipment, please power down all components.
Projecting from a laptop
If the ēno receiver LED is Green and…
Flashes five times after you attempted pairing, the stylus and the ēno receiver have been successfully paired.
Flashes three times when you removed the stylus cap (after the stylus has been paired and the ēno App 3.0 or higher is running), the ēno stylus has successfully re-connected to your computer.
Is solid blue, the ēno App is communicating with the ēno receiver.
Is flashing as you use the stylus, data is streaming from the ēno stylus to your computer successfully.
Quickly flashes five times after you attempted pairing, the stylus and the ēno receiver have not been successfully paired. You need to start the pairing process over again.
Flashes three times when you removed the stylus cap (after the ēno stylus has been paired and the ēno App 3.0 or higher is running), the ēno stylus has not been successfully connected to your computer. You need to cap and uncap the stylus again.
Is solid red, the ēno App is not updated to version 3.0 or higher, or the driver is not running. Launch the ēno App version 3.0 or higher on your computer and start the pairing process over again.
It may be necessary to calibrate the whiteboard with the computer desktop. This assures that the location the stylus tip touches the whiteboard exactly corresponds to the projected computer cursor and pen.
To calibrate the ēno whiteboard with the projected host computer:
- Use the ēno stylus to tap the Calibrate icon on the ēno icon strip one time.
- Use the ēno stylus to tap each target projected on the whiteboard, following the instructions you see on the whiteboard.
- When calibration is complete, you are ready to begin using the stylus to interact with the computer.
Mouse control using the ēno stylus:
To use the stylus as your mouse for controlling the host computer from the whiteboard:
Tap the Mouse icon on the icon strip.
Or tap the File icon on the icon strip.
To double-click, tap twice rapidly. Be sure to tap twice without moving the stylus.
To type, tap the Keyboard icon for access to your computer operating system on- screen keyboard. Refer to “Using the on-screen keyboard” on page 27 of the full User Guide.
For a right-click (Windows) or control-click (Macintosh), tap and hold the stylus tip (without moving it) on the whiteboard for one second.
To open the folder on your computer where you last saved an ēno snapshot file, tap the File icon.
To pass the “back” or “forward” command to the active application, tap the Left or Right arrow icons.
To pass the undo or redo command to the active application, tap the Undo or Redo icon.
The ēno icon strip legend:
Connect the laptop VGA cable or the HDMI cable from the top of the podium to the corresponding port on your laptop.
Press the Power button on the projector remote to activate the projector.
Press the source button that corresponds with the video cable you are using, either DVI-I 3 (for VGA) or HDMI 6 button.
For audio, plug the 3.5mm audio cable on the top of the rack into the headphone port on your laptop.
Audio volume can be adjusted on the computer using the speaker icon in the taskbar or by using the audio adjustment dials on the front of the speaker.
When you are finished using the equipment, please
What are ēno interactive whiteboards?
ēno interactive whiteboards provide cordless interactivity with a computer using the Bluetooth-enabled ēno stylus. While the computer is projected onto the ēno interactive whiteboard, use the stylus to:
- enhance presentations by enabling interaction and collaboration
- navigate through documents, presentations, or websites from the whiteboard
- write, highlight, and erase notes
- print and save your work
ēno interactive whiteboards are made from ceramicsteel so you can also use them with dry-erase markers and magnets as well as the stylus.
Instructional Technology staff are happy to train anyone on the use of the ēno interactive whiteboard. During the session we will install the required software, pair the stylus with your computer and provide instruction on using the system. We invite anyone to request training on this system. Please contact Jedidiah Rex or Adam Dinnes to schedule a training session.
Pairing the ēno stylus with the ēno receiver:
The ēno receiver connects to your computer’s USB port and pairs the Bluetooth signal with the ēno stylus. You can pair up to three ēno styli to one ēno receiver.
- Power On your computer and assure that the ēno App version 3.0 or higher has already been installed. This software will be installed on your machine during the required training session..
- Connect the ēno receiver to a USB port on the your computer.
- Power On the ēno stylus by removing the cap.
- Wait for the stylus LED to blink green once every three seconds.
- Press and release the Pair button on the ēno receiver to pair the Bluetooth signal with the stylus.
- While the ēno receiver searches for the ēno stylus Bluetooth signal, a status message appears on the computer screen and the LED on the ēno receiver flashes green.
- If pairing is not successful, a status message appears on the computer screen.
- If pairing was not successful, you can try to resolve the problem by removing the ēno receiver from the USB port, waiting five seconds, and reinserting it before attempting the pairing process again.
- If pairing was not successful, refer to the Stylus LED status and troubleshooting section on page five.
- After pairing is successful (within 30 seconds), the status message on the computer screen indicates that ēno is ready to use and the ēno receiver LED changes to a solid blue color.
Stylus LED status summary and troubleshooting:
power down all components.
Projecting the built-in Blu-Ray player
Turn the projector ON using the Power button on the projector remote.
Press the Power button on the projector remote to activate the projector.
Press the Eject button on the Blu-Ray player to insert your disc, then press the Eject button again to close the tray.
Press the Video 4 source button on the remote to display the Blu-Ray player.
Control the video using the Blu-Ray player remote.
Audio volume can be adjusted using the control knobs on the front of the speaker.
When you are finished using the equipment, please power down all components.
